www.manfrotto-shop.ch

MA FF3210 MOUNT BRACKET F/CEILING BLK 

Bracket for ceiling attachment of the rail. It is advisable to pre-assemble these brackets onto the rails at ground level to ensure correct alignment before screwing to a ceiling.  

MA  FF3212 MTG BRACKET FOR BEAMS

Bracket for wall attachment of the rail.  

MA FF3211 DOUBLE BRKT.F/R CROSSING 0951 

This is used to permanently attach two rails at a right angle or parallel.  

MA FF3215 ADJUSTABLE MOUNTING BRKT(0942)

Allows height differences in ceilings of maximum 2 cm; combining two brackets you can compensate for differences of maximum 4 cm.  

MA FF3207 PACK OF 4 END STOPS BLK (0953)

These fit to the holes on the ends of a rail to prevent carriages leaving the rail and to prevent moving rails leaving their carriages. IMPORTANT: must be fitted to upper and lower holes on moving rails but only to lower holes on fixed rails.  

 MA FF3208 RAIL CONNECTOR

A pair of clamp plates with screws to join two fixed rails together by clamping across the junction on the upper guide, using holes provided in the rail. IMPORTANT: the junction must always be supported by a rail-mounting bracket placed astride  

MA FF3214 GIRDER MOUNTING BRACKET

This can be fastened to tubes with diameters from 35 mm to 50 mm inclusive. It's used to directly support the rail that can be fixed in place either longitudinally or transversely. This bracket can be used as a brace for fixed supports, as well.  

MA FF3214A THREADED MT BRKT W/O ROD(0961) 

Can be attached directly by screws or rods with a maximum diameter of 1/2". Before mounting the bracket it is advisable to standardize the length of both the rods and screws. Fix the bracket between a nut allowing the screw on the inside of the bracket to protrude about 1,5 cm. When fixture is completed, it is then possible to regulate a perfect rail levelness by adjusting the nuts which fasten the brackets.  

MA  FF3214B CEILING BRACKET W/THREADED ROD 

Comprised of a bracket to be attached to the ceiling with 4 screws, a 1 m long M12 rod completely threaded, 4 M12 nuts, and a bracket for the rail fixture. The rod can be cut to the desidered size and then attached to the bracket by way of the nuts supplied. The rod must protrude approx 1 cm on the inside of the bracket. When fixture is completed, it is then possible to regulate a perfect rail levelness by adjusting the nuts which fasten the brackets.  

MA FF3215A EXTNSN BRCKT F/VARIOUS HEIGHTS

Its length is adjustable from 10 cm to 15,5 cm. Using the clamp screw, you can obtain all intermediate sizes. Provided with a security lock, in case the regulating screw loosens, blocks the bracket at maximum extension. It's used to compensate for height differences in ceilings of 5,5cm or more, with combinations of other brackets. It's also used for obtaining intermediate sizes in combination with the extendable ceiling brackets.  

 MA  FF3216 CEILING BRACKET 30CM

MA  FF3218 CEILING BRACKET 50CM

 MA FF3220 CEILING BRACKET 100CM

Used alone or in combinated these brakets allow the attachment of the rails at the desidered height.  

MA FF3228 DISMOUNTABLE CARRIAGE BLACK

This carriage can be inserted directly at any point on the rail by unscrewing the wheel plate. This is used when it becomes necessary to add a supplementary carriage to an already assembled RAIL SYSTEM installation. It is free-sliding and is suitable for normal loads.  

 MA FF3229 CARRIAGE W/BRAKE BLK (0926)

This is provided with a brake which keeps it locked in the position where it is placed. It is suitable for normal loads up to 60 kg. To release brake pull down on wire with operating pole.  

MA FF3230 SINGLE CARRIAGE BLACK

It is free-sliding carriage. It is suitable for normal weight loads up to 60 kg.  

MA FF3232 DOUBLE CARRIAGE

Both the upper carriage and the lower one are free-sliding.  

MA FF3235 DOUBLE CARR W/BRAKE BLK (0922)

This is equipped with brakes on both upper and lower carriages. The upper brake blocks the carriage on the fixed rail, while the lower carriage's brake blocks the sliding of the moving rail.  

MA  FF3236 DOUBLE CARRIAGE W/SINGLE BRAKE

This is provided with a brake on only one carriage. Normally, the carriage with brake is mounted on the fixed rail so that it is locked into place enabling the mobile rail to slide. If the carriage with brake is mounted onto the mobile rail, you obtain the opposite effect, that is, the sliding of the mobile rail gets blocked, while the carriage can freely slide on the fixed rail.  

 MA FF3325 DOUBLE CARRIAGE TO MATCH 0979 

It is used together with the motorized carriage code FF3350. The upper carriage, is as high as the motorized carriage. Both the upper carriages and the lower one are free-sliding.  

MA FF3340 MOTORIZED CARRIAGE 

It is powered with a 24 Vdc motor and must be fed and operated by an electronic power supply, code FF3288M/FF3286M.  

MA FF3350 DOUBLE MOTORIZED CARRIAGE 

The upper carriage is powered by a 24 Vdc motor which must be fed and operated by an electronic power supply code FF3288M/FF3286M. The lower carriage is equipped with a brake which blocks the mobile rail from sliding.  

MA FF3450 ROTA LITE 

Motorised head with 2 motors for the rotation made up of a small bank, flash or television camera. It has a 16 mm spigot on both sides. It can be positioned between a pantograph and utilisation (illuminator, small bank, flash, video camera, etc.) or it can also be mounted onto a stand. It allows a combined rotation of 360° on axis X and 110° on axis Y. It is powered by two 24 Vdc motors that must be fed and operated by an electronic power supply FF3288M/FF3286M1; motor powers the rotation on axis X and the other on the axis Y.  

MA FF3221 FIXED BRACKET -5/8 FEMALE 0958

The 16 mm socket allows the mounting of lights or accessories with 16 mm male attachments.  

MA FF3224 PAIR OF BACKGROUND SUPPORTS

These can be fixed directly onto the rails in order to have the backgrounds in a fixed position, or they can be fixed to simple carriages with the help of the fixed brackets code FF3221, in order to have a background in a movable position.  

MA  FF3226 PACK OF 5 CABLE RUNNER BLACK

These are inserted from the end of the rail. They do not need wheels as they they slide along the rail and are suitable for normal cables.  

MA FF3226S PK/5 DISMTABLE CABLE RUN BLACK 

By slightly opening them, they can be inserted at any point on the rail. They are suitable for light weight cables.  

 MA  FF3226V LARGE CABLE CARRIAGE 0938HD

Runs on ball bearings. Holds cables up to 16 mm diameter.  

MA FF3856 BRACKET WITH 16MM SPIGOT

The 16 mm spigot allow the mounting of lights or accessories with 16 mm female attachment.  

Manfrotto MA  013 ADAPTER SPIGOT

Universal 16 mm spigot with double male thread 1/4" and 3/8".

Manfrotto 013 Ersetzt :
2972
3094

MA  FF3257 ADAPTER 5/8F TO 1 1/8F 0932

It has a 16 mm female attachment on one side and a 28 fermale attachment on the other. It is used to fit accessories with 28 spigot to the RAIL SYSTEM.  

MA  FF3260 ADAPTER 5/8F TO 1 1/8F 0931 

This adapter has a 16mm spigot on one side and a 28 mm female attachment on the other. It is used to connect accessories with 28 mm spigot to the RAIL SYSTEM. It comes complete with safety pins.  

MA FF3261 BALANCE ADJUSTMENT BRACKET

It has 16 mm female attachment, to be fitted between pantograph und unbalaced lighting fixtures or other appliances. Easy adjustment, by means of a single lever, allows the pantographs to work properly.  

MA  362 POLE OPERATED TELESCOPIC BAR

Designed to support heavy light fittings, and provide pole operated pan plus tilt.  

MA FF3262 BRACKET F/MULTIPLE MTS 0955

 MA FF3265 UNIVERSAL SUPPORT F/PACKS

A 16 mm spigot mounted on the bracket allows fitting to RAIL SYSTEM.  

MA FF3272 AERIAL OUTLT- W/3 UNIVSL SOCKT

It has a 16 mm female attachment with shear pin and locking screw. Comes complete with 5 m of three-pole cable (3 x 1,5 Sq.mm) without plug. Max load 2000 Watts.  

MA FF3278 40 FT POWER CABLE

15 m of three-core cable (3 x 1.5 Sqmm) with special sockets for lighting fixture.  

MA FF3512N86 PANTOGRAPH 2,0M W/5/8"ATTACHM.

The pantograph is made of aluminium (P-Al MgSi UNI 3569) and manufactured according to DIN 15560-46. The attachments at both ends of the pantograph are 16mm, male on the bottom and female on the top. The load is supported by a steel cable of 2 mm. diameter (safety factor 12). Loads up to 12 Kg can be suspended using only the patented friction device, while loads up to a maximum of 18 kg require the use of the optional springs. The pantograph can be regulated to keep suspended loads from 1 to 18 kg perfectly balanced. By turning the coulored notched ring you can adjust the pantograph’s friction; this will ensure that the load remains stable when set in position, but that it will move smoothly up and down when necessary. In any case, it is always advisable to use the springs to aid raising your pantograph When choosing the additional spring(s) for your pantograph, you will first need to know exactly which model of pantograph you have, in order that you can select the spring of the correct length. If you have one of the new compact pantographs (with grey-painted "scissors"), look at the colour of notched ring the 2 m version has a red notched ring, while the 3.8 m version has a blue notched ring. After having identified the length of the pantograph, choose the appropriate spring(s) by refering to the table below.